- News
- Reviews
- Bikes
- Accessories
- Accessories - misc
- Computer mounts
- Bags
- Bar ends
- Bike bags & cases
- Bottle cages
- Bottles
- Cameras
- Car racks
- Child seats
- Computers
- Glasses
- GPS units
- Helmets
- Lights - front
- Lights - rear
- Lights - sets
- Locks
- Mirrors
- Mudguards
- Racks
- Pumps & CO2 inflators
- Puncture kits
- Reflectives
- Smart watches
- Stands and racks
- Trailers
- Clothing
- Components
- Bar tape & grips
- Bottom brackets
- Brake & gear cables
- Brake & STI levers
- Brake pads & spares
- Brakes
- Cassettes & freewheels
- Chains
- Chainsets & chainrings
- Derailleurs - front
- Derailleurs - rear
- Forks
- Gear levers & shifters
- Groupsets
- Handlebars & extensions
- Headsets
- Hubs
- Inner tubes
- Pedals
- Quick releases & skewers
- Saddles
- Seatposts
- Stems
- Wheels
- Tyres
- Health, fitness and nutrition
- Tools and workshop
- Miscellaneous
- Buyers Guides
- Features
- Forum
- Recommends
- Podcast
feature
Tubeless inserts for less than £10 - a cheap way to upgrade your gravel bike
Fitting a set of tubeless inserts to a road, cyclocross or gravel bike is a great way to ensure that your tyre isn’t going to roll off the rim at low pressures, it adds some protection when riding over rocks and roots, and it means that you can continue riding should your sealant be unable to plug a hole. But branded inserts are very expensive, so we made our own.
What you need
- PU Backer Rod - we’re still not 100% sure what this is actually for in the real world
- Tubeless valves - Come with most wheels these days
- Tubeless sealant - We used Stans
- Tyre levers
- A pump
- A can-do attitude - not essential
The PU backer rod comes in 5mm diameter increments and you want the size below the tyre you’re installing. So for our 33mm cyclocross tyres, we got the 30mm size. You can get larger sizes for gravel tyres here, but after 30mm it comes in 10mm increments.
It is a closed-cell design and waterproof, so it shouldn't soak up all of your sealant.
Process
The process is very simple so I won’t bore you with too much detail. First of all you don’t start doing this in the living room. In the bath, outside or anywhere that has a wipeable surface is how you avoid getting into trouble with husband/wife/parents/housemate/partner. You have been warned.
You pop one side of the tyre off and start just to one side of the valve. Tuck the liner all the way around, making sure to roll it onto the rim before cutting so that you finish just short of the valve. That’ll allow air to pass freely.
> Tubeless inserts - the next big advance in road tubeless tech?
Then it’s simply a case of pushing the tyre bead on. This will be tight, so make sure you push it down into the rim well and finish at the valve.
Drop some sealant in and you’re good to go.
Cost
It is worth pointing out that buying a set of tubeless inserts will usually mean that you also get some sealant and tubeless valves. Our budget version doesn’t come with those things, but if you have sealant and valves lying around already, then you shouldn’t need more.
10m of the backer rod cost us £7.29, so we’ve got enough to do roughly 5 wheelsets and that, compared to a set of Vittoria Tubeless Air Liners at about £70 for one wheelset, is a rather good bargain.
Even if they need changing more frequently, you’re still going to be making a saving.
Results
To test these out we jumped on the cyclocross bike and rolled down to the local park. Conditions were dry, so there was plenty of grip, but we slowly lowered the tyre pressures to those that you’d only ride in the muddiest race. Cornering at a decent speed didn’t cause any burping of air and neither did some poorly executed hopping of a makeshift barrier.
> Review: Vittoria Air Liner Tubeless Inserts
So if you’re looking to reap the benefits of tubeless inserts but the cost has always put you off, give ours a go and let us know how you get on.
Latest Comments
- Rendel Harris 0 sec ago
It's a warning that pickpockets are targetting elderly Morphs.
- slc 6 min 20 sec ago
Don't forget that in the future, everyone will be one size, or convenient multiples thereof. Same bodies, same homes, same jobs, same bikes. No...
- andystow 2 hours 4 min ago
Based on my experience with the Hunt wheels, I might do a review on their durability in three or four years.
- Destroyer666 6 hours 30 min ago
"...the beeswax-based covering magically shuns off whatever might be lurking in the corners. Even after multiple rides, when the bars rattled about...
- David9694 7 hours 53 min ago
t-boned
- Rendel Harris 9 hours 13 min ago
I didn't know the blue RA saddle was a holy grail - I had a 1986 RA bought new in 1987 with a blue saddle that lasted me very well until 2002 when...
- newbankgyratory 9 hours 23 min ago
Solution: Put these up everywhere. Source: https://www.gov.uk/guidance/the-highway-code/traffic-signs
- Rendel Harris 10 hours 21 min ago
Glad you like it - this week was the first proper commuting week since I got it, 250kms nice and warm but not boiled, indeed - and when the...
- Rendel Harris 11 hours 53 min ago
As what you have said is demonstrably untrue, given that the event is organised and has been for the last four years by a professional events...
- Steve K 13 hours 37 min ago
I'm there now too, if anyone wants a follow/wants to follow me. @cyclingtheseaso
Add new comment
20 comments
I live in Colorado, USA and have a gravel bike. My rims are 19mm interior width and I'm still running the stock tires, Vittoria Terreno Zero's 700-38c. They measure about 41mm wide on the outside so I suspect they probably are 38mm inside.
From your article it sounds like the largest backer rod that would fit my tires is the 30mm, just like you used for your 33mm cyclocross tires, but my tires are 5mm wider. Do you think it would it still work?
Perhaps more importantly, people over here are stuck on the stupid system when it comes to units of measure and I can't get metric backer rod. My 38mm tire cavity converts to 1.496 inches. I don't think 1.5" rod would fit. 1.25" rod is 31.75mm, so that might work, but I can only find it in bulk. It was around $80 for 100' or $135 for 400'.
If I'm gonna spend $80 I might as well get Vittoria Air-Liner Gravel inserts to match my tires tho right?
My goal is to hold the tire on the rim (stop blow offs after large sidewall punctures) and get run flat capability for emergency situations in which I can't get home using extra sealant, bacon, CO2 and a frame pump alone.
Also, my tires are both FULL of thorns inside and out so installing a tube isn't an option (I ride on carpets of goathead vines occasionally). The tube is normally a last resort backup but I don't even carry one so I'm hoping inserts can serve as that backup for me.
I'd appreciate any advice, whether it's about which commercial liner might be the best option or a way to pull of this clever foam backer rod trick here in rural Colorado. Thanks in advance!
I used something similar for the Three Peaks CX one year and in short, backer rod isn't up to the job for preventing pinch punctures, as the foam isn't dense enough. It did let me ride on a flat back tyre for a mile or so. Also it was really handy for plugging gaps when I redid the weather seal around our front door.
This video encapsulates perfectly why I have no interest in such a messy, complicated and time-consuming system. I give thanks for tubes on a daily basis.
Messy and complicated, requiring new tools...
But...
The day you ride down a country lane during hedge cutting season, pulling multiple inch long thorns out of the tyre and watching them seal, and then finding many more when you get home.
Or pulling out the sharks tooth flint on the rainy night, it not sealing on its own, but getting to use the anchovy and stabby tool.
I get what your saying but a point. You are far less likely to have a puncture and when you do you are unlikely to need to stop. Think I had 2 punctures last season and stopped zero times normal notice was a bike that needed a clean . On group rides of 8 people we would average 1 puncture every 2-3 rides wasting my time especially the fun double punctures. When you crack the setup it's really easy. I always do them outside and always have a hose ready to wash the gunk away. It's just different!
People online say they'll never go tubeless a lot, and it's fine, but I think you should realize that you're also saying there are places where you'll never bike. The agricultural access roads in NE Colorado make some great rides but you'd be crazy to try them with tubes.
PU Backer Rod is used for packing expansion gaps before sealing it with adhesive/silicone.
It's made by - amongst others - Soudal. Perfect for that Ridley you bought with your winnings from the Belgian Lottery.
Thanks - looks worth a go. How much tolerance can one have e.g. on a 38mm tyre is 30mm insert too loose? Equally is a 30mm insert too right on a 30mm tyre (I guess the latter depends more on true inflated width if tyre?)
Is any good for road tyres?
Currently running tubed Marathon Plus on the commute and we all know what pig these can be.
As close to indestructible as they seem to be, something will eventually get through them and I'd rather not be in the middle of Shettleston High Street when something does.
Something will eventually get through them. In my case, it was a nail that went in through one side of the tyre and out the other. Even then, the things are so stiff I managed to finish my commute before I noticed.
All the pictures are done with aero road wheel sets so I would think it's fine.
These are for tubeless wheels/tyres, so no good for tubed tyres.
Don't suppose you know of any tubless equivallents to the MPs?
Not really equivalents as the MPs have extra tough/stiff casing to prevent punctures and tubeless tyres rely on the sealant inside to seal small punctures, so they're thin and flexible. I like the GP5000TLs but they're not cheap and they won't last as long as Marathon Plus.
MPs have extra tough/stiff casing to prevent punctures
Well, they don't prevent punctures, but they do markedly reduce the frequency. I recently had a front puncture, which was the first for over a year since I put on the MPs for the Pennine Bridleway. It was, of course, a hawthorn which had made its way through the off-centre 'valley' in the tread on the sidewall
I'm using the Pirelli cinturato currently, more of a tubeless gatorskin hardshell than marathon plus but so far so good.
It's hard to believe but you don't need reinforced tires once you go tubeless.
My gravel bike came with tires softer than butter. In the first 210 miles I had 22 punctures using tubes, mostly on pavement. I went tubeless after that and unless I'm literally riding on goathead vines for more than a few hundred feet or get a large puncture that doesn't seal I don't even have to stop to add air.
My old ten speed has gatorskins and tire liners protecting the tubes. That's finally stopped almost all flats but during goathead season there's always a thorn or two that gets thru the sidewall and misses the liner.
So I'd say it's either tons of armor around a tube, or tubless, you don't need both.
I wondered if something similar could coexist with a tube - the pu backer rod looks as if it's made from the same stuff as pipe lagging. Might a narrow tube surrounded by pipe lagging cut in half lengthways do a job within a wide tyre?
If I got many punctures on my wide (38 mm) clincher-tyred bike I might try it - but I've had only 2 in 10,000 odd km so not much need really.
I think you need Youtube!
There are videos of almost every possible inner tube replacement being tested including multiple goes at the one you suggest.
A useful maxim to live by (says man from Edinburgh, tongue in cheek).