- News
- Reviews
- Bikes
- Accessories
- Accessories - misc
- Computer mounts
- Bags
- Bar ends
- Bike bags & cases
- Bottle cages
- Bottles
- Cameras
- Car racks
- Child seats
- Computers
- Glasses
- GPS units
- Helmets
- Lights - front
- Lights - rear
- Lights - sets
- Locks
- Mirrors
- Mudguards
- Racks
- Pumps & CO2 inflators
- Puncture kits
- Reflectives
- Smart watches
- Stands and racks
- Trailers
- Clothing
- Components
- Bar tape & grips
- Bottom brackets
- Brake & gear cables
- Brake & STI levers
- Brake pads & spares
- Brakes
- Cassettes & freewheels
- Chains
- Chainsets & chainrings
- Derailleurs - front
- Derailleurs - rear
- Forks
- Gear levers & shifters
- Groupsets
- Handlebars & extensions
- Headsets
- Hubs
- Inner tubes
- Pedals
- Quick releases & skewers
- Saddles
- Seatposts
- Stems
- Wheels
- Tyres
- Health, fitness and nutrition
- Tools and workshop
- Miscellaneous
- Tubeless valves
- Buyers Guides
- Features
- Forum
- Recommends
- Podcast
forum
Disc callipers with Mtb levers?
I am looking to convert a drop bar bike to flat bars and am running Tiagra hydraulic discs. Can I use any of the Shimano mtb levers with the callipers or will I need a complete setup? If I need a whole new system is there a reasonable priced flat bar/flat mount system out there worth looking at?
If you're new please join in and if you have questions pop them below and the forum regulars will answer as best we can.
Latest Forum Topics
Latest Comments
- chrisonabike 2 sec ago
If the fee covers pollution who pays for the cost of maintaining a vast network of roads far wider / built to weight-bearing standard far greater ...
- brooksby 5 min 26 sec ago
Over 8,000 caught breaking 20mph limit on one road (BBC) https://www.bbc.co.uk/news/articles/c4gx7ygn73yo
- brooksby 27 min 43 sec ago
Well, one of them isn't telling the truth…
- Rendel Harris 2 hours 5 min ago
Well yes, could do but a 2020 onwards Ultegra crank is no more likely to snap than a 105. By no means a gear [pun intended] snob, my stable has...
- chrisonabike 8 hours 57 min ago
Presumably a) expense b) for something that (mostly) works against your customers' convenience? And the usual "but emergencies - what about when...
- quiff 13 hours 23 min ago
I was going to suggest the Fairlight Strael too, and went to check if it came in on budget. While there, I finally ordered the frameset I've been...
- quiff 16 hours 18 min ago
"No darling, I said a cactus bike holder, not a bike cactus holder."...
- Andrewbanshee 18 hours 33 min ago
I have visited Guernsey and my wife goes there a few times a year for work. This act of premeditated violence shocks me. There are quite a lot of...
- hawkinspeter 18 hours 59 min ago
You could well be right. Personally, I think Avonvale Rd is just a disaster for having two way traffic. So many drivers think the traffic calming...
- hawkinspeter 19 hours 6 min ago
Although Muller Rd isn't great to cycle on (the north end, anyhow), it's certainly not the worst. I'm definitely in the "brave and bold cyclist" at...
Add new comment
3 comments
Hi, I'm not certain but I think for hydraulic brake systems the levers & calipers must be the same. I'd guess it's something to do with the volume of fluid pushed by the levers matching the volume of the pots in the calipers? The good news is that perfectly serviceable MTB brake kit is dirt cheap by road standards (little bit heavier but hey!). Quality is amazing. I have SLX brakes (umm, iirc about £70 x 2 10 years ago) on my MTB & they've never needed bleeding in the 10 years since I built the bike!
MTB brakes are all post mount but Shimano does a flat mount adapter, widely available for about a tenner a pair, so no probs mounting on a bike with flat mount (I have another bike with this arrangement). Note there doesn't seem to be any way to do the reverse, mount a flat mount brake on a post mount bike.
One other thought on this, I suspect MTB brakes will need at least a 160mm disc rotor, but that just means you have better brakes.
I have a flat bar road bike & it's an absolute dream - light, flicky, manoueverable & comfortable & the straight bars give far better & more natural handling than you'll ever get with drops. I use small bar ends to give me a sort of on-the-hoods option. Just don't expect to be toughing it out with the big boys in the final sprint...
You might have an issue with gears. I found MTB gears a bit stiff for my straight bar road bike build - they need stronger clutch springs to limit chain slap when bouncing around off road. Even top-end MTB gears feel like trying to pull bricks through a bush compared with Ultegra. In the end I settled on a SRAM 1x road group (Apex-1 @ t'mo, but I may upgrade to Rival-1 sometime) coz (a) I'm never in a hurry & 1x is beautifully simple, & (b) SRAM make flat bar levers for their road groupsets (altho they might take some finding post-Brexit, pre-Brexit I got mine from Germany).
Hope that helps. Good luck & good hunting!
I've been running mountain bike calipers (SLX M7000) with road shifters (RS505) with no issues.
Can't see why that wouldn't work in reverse.
If that fails a full set of SLX7000 brakes and calipers is £150. Far more sensible prices in the world of baggy shorts.
Thanks Rich, at £14 each for Deore M4100 levers I will give it a try